Fogging Tester
Standards
- DIN 75201: Automotive trim material fogging resistance.
- ISO 6452: Coated fabrics fogging behavior in vehicle interiors.
- SAE J1756: Automotive interior material fogging test protocol.
- BS EN 14288 & QB/T 2728: Leather and textile fogging evaluation.
- PV 3920/3015: VDA-standard fog value determination for non-metallic materials.
- ES-X83231, NES M0161, GM 9305P: OEM-specific fogging requirements for automotive suppliers.
Product Advantages
- Triple Testing Modes: Supports gloss, gravimetric, and haze analysis for comprehensive material evaluation.
- Precision Temperature Control: ±0.1°C accuracy across high/low baths (room temperature to 150°C) ensures repeatable results.
- Six-Station Efficiency: Simultaneous testing of six samples accelerates R&D and QC workflows.
- Corrosion-Resistant Design: 316 stainless steel test chambers and epoxy-coated steel frame withstand harsh chemical environments.
- Advanced Safety: Magnetic safety switch, over-temperature thermostat, and audible test-completion alerts.
- Data Connectivity: USB port and multi-function sensors enable seamless integration with lab information systems.
Product Features
- Dual-Bath System:
- High-Temperature Bath: 670×490×540mm, 3kW heating power (up to 150°C).
- Low-Temperature Bath: 400×220×520mm, 500W cooling capacity (0–100°C).
- Automated Controls:
- Digital thermoregulator with microprocessor for precise temperature programming.
- Programmable timer (1–9999 min) with auto-stop and end-test buzzer.
- Modular Accessories:
- 18/8 stainless steel test cups, flat beakers, and chrome steel rings for sample mounting.
- Six interchangeable cooling plates and haze/gloss measurement kits.
- Safety Compliance:
- CE-certified with anti-acid epoxy coating, emergency stop, and overpressure relief.
Technical Parameters
| Parameter | Specification |
|---|---|
| High-Temperature Range | Room temperature – 150°C (280°C optional) |
| Low-Temperature Range | 0–100°C |
| Temperature Stability | ±0.1°C (at 200°C) |
| Heat-Up Time | <45 min (to 150°C) |
| Cooling Capacity | 500W (low bath) |
| Power Supply | AC 220V, 50Hz, 3.5kW |
| Dimensions | 500 (W) × 650 (D) × 600 (H) mm |
| Net Weight | 50 kg (excluding thermal media) |
| Data Interface | USB 2.0, remote sensor compatibility |
| Safety Systems | Magnetic switch, thermostat, audible alerts |
在线联系供应商
Other supplier products
 |
New warm body dummy tester-QINSUN | Product Description In addition to heat dissipation to the surrounding environment through conduction, convection and radiation, the human body al... |
 |
Automotive Wires Dynamic Bending Tester | Standard ISO 6722: Road vehicles – Flexible cables for wiring harnesses. SAE J1128: Low-voltage primary cable for automotive applicatio... |
 |
Multi-Finger Scratch/Mar Tester | Standards Chrysler LP-463DD-18-01 Scratch and Mar Resistance of Automotive Plastics Chrysler PF-10938 Scratch and Mar - Resistance of Molded-In-C... |
 |
MARK-II Slip Resistance Tester | Product Introduction: Paste the cut sample on the test fixture of the portable MARK-II anti-slip testing machine, put down the weight of the rotat... |
 |
Shoelace Abrasion Tester | Standards SATRA TM93、DIN-4843、QB/T2226、SATRA TM154 Principle Let shoelace cross the eyelet clamped on the fiber board, make the shoelace and eye... |
Same products
 |
Seat Bumping and Creep Test Bench | 卖方: Standard International Group (HK) Limited | This test bench is used for simulating the car seat bumping and creep situation when a car is run... |
 |
Automobile seat belt fixed point test bench | 卖方: Standard International Group (HK) Limited | Applicable standards: National mandatory standards: GB 15083-2006"Automobile seats, seat fixtur... |
 |
Impact strength tester for car seat headrest | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 15083-2006 "Automobile seats, seat fixtures and headrest strength requi... |
 |
Impact strength tester for car seat launching headrest | 卖方: Standard International Group (HK) Limited | Main parameters: Impact speed:The impact speed of the tester is usually between 25 and 30km/h, w... |
 |
Automobile Headrest Strength Tester | 卖方: Standard International Group (HK) Limited | Applicable standards: GB 11550-2009"Automobile seat headrest strength requirements and test me... |
