Safety Helmet Electrical Insulation Tester GB/T2811
Product Introduction:
Safety hat electrical insulation performance tester used to test the electrical insulation performance of safety hat, high degree of automation, easy to operate, widely used in safety hat manufacturers and major quality inspection units.
Meet the standard:
GB/T2812-2006 Safety helmet test method
GB/T2811-2007 Safety helmet
Product Features:
Plastic sink or water bath system designed to contain water and accommodate the safety helmet for testing in a wet condition, without interfering with electrical measurements.
Electrodes for applying high voltage to the safety helmet, including a probe with a specific diameter (4mm) and hemispherical top.
LED digital display providing real-time readouts of current and voltage values during the test.
Capability to apply high voltage according to a specific sequence: increasing the voltage to 1200V ± 25V within 1 minute and maintaining it for 15 seconds.
Voltage regulator with a range of 1500V to control the applied voltage.
Built-in timer to control the duration of the high-voltage application, with a specified error ($pm$1%).
Accurate measurement of current and voltage, with expression value errors of $pm$1%.
Configurable test head die or electrode to meet various helmet testing requirements.
High level of automation for the test procedure.
Safety features (implied for high voltage testing) to protect the operator.
Technical parameters:
1. the current expression value error of ±1%
2. voltage value error ±1%
3. timer value error ±1%
4. the diameter of the probe is 4mm, the top is hemispherical
5. The voltage is increased to 1200V±25V within 1min and maintained for 15s
6. voltage regulator: range 1500V
Send product request
Other supplier products
 |
STD G651 national standard shoe bending tester | Product Introduction: National standard shoe bending testing machine is specialized in testing finished shoes and soles, after a long time, fixed ... |
 |
Multilayer geotextile single-layer thickness tester丨IS0 9863 | Meet the standard GB/T17598-1998. GB/T 13761.1-2022. JTG E50-2006. IS09863-90 Scope of application The multi-layer sample is mechanically separa... |
 |
Safety shoe impact testing machine / Safety shoes testing machine | According to the criteria Bs-953.1870 EN-344. ANSI-Z41 CSA-Z195 ISO K88782 EN ISO 20344. ANSI-Z41 BS EN-344 CSA-ZI95 LD50-1994 Product F... |
 |
Aluminum Tube Internal Coating Continuity Tester | The continuity tester for the inner coating of aluminum tubes is an important device specifically used to detect the continuity of the inner coatin... |
 |
Thermal - Cold Cycle Testing Machine / Hot and Cold Thermal Cycling Testers | Standard BS 7291: Compliant for thermal cycling tests on thermoplastic pipe systems (1769 Series with pressure chamber). Adaptive Certification: ... |
Same products
 |
Bottle Wall and Bottom Thickness Tester | Seller: Standard International Group (HK) Limited | The wall and bottom thickness tester for bottles is a measuring instrument widely used in the pha... |
 |
Pinhole Tester / Pinhole Testing Equipment | Seller: Standard International Group (HK) Limited | The pinhole tester for aluminum foil is a device specifically used to detect micro - pinholes in ... |
 |
Cork Puncture and Chip Detection Instrument | Seller: Standard International Group (HK) Limited | The rubber stopper puncture debris detector is a device specifically used to detect the number of... |
 |
Aluminum Ointment Tube Toughness Tester | Seller: Standard International Group (HK) Limited | The ductility tester for aluminum tubes is a device specifically used to detect the ductility ind... |
 |
Vacuum leak tester / Vacuum leak instrument | Seller: Standard International Group (HK) Limited | Vacuum Decay Leak Tester specializes in the detection of leaks in ampoules, vials, injection bott... |
